Tempe is a city where the housing stock covers a wide range: apartment buildings and student rentals alongside single-family homes, commercial properties mixed with older residential blocks, and plenty of units that have been updated piecemeal over the years without a full electrical review. The electrical work that comes out of a place this size reflects that mix. A property manager dealing with a tenant move-in has different needs than a homeowner who has never looked at the panel since they bought the place. We handle both, and everything in between.
What stays the same across all of it is how the call goes. You describe what is happening, we ask the right questions to scope the job, and you get a price before anything is scheduled. We cover Tempe and the surrounding Maricopa County area, available every day from 5:00 AM to 10:30 PM.
Call (480) 923-2895 to get started.
A lot of electrical problems in a city like Tempe are not sudden. They have been there for a while. An outlet on the back wall of a bedroom that has never worked since the current tenant moved in. A switch near the front door that gives a small spark when it is flipped. An exterior light over the garage that stopped working two winters ago and just never got addressed. These are the calls that get put off because nothing has caught fire yet.
The reason they are worth making sooner is that each one is pointing at something. A dead outlet often traces back to a tripped GFCI device somewhere upstream, but it can also mean a loose connection or a wiring fault in the wall. A sparking switch is a worn contact or a ground issue that does not improve with time. An outdoor fixture that went dark may have lost its weatherproof seal, letting moisture reach the wiring behind it. None of these is a wait-and-see situation. One call gets the problem looked at properly.
Apartment buildings and older single-family homes in Tempe sometimes carry wiring that has been added to over the years without a clear picture of the whole system. A circuit that was fine when one appliance was on it starts tripping once a second or third load is added. Junction boxes that were covered rather than properly closed. Grounding that was never confirmed. These are not unusual findings, and they do not always mean a major project. Sometimes the fix is straightforward once the fault is traced. Sometimes it points to a section of wiring that needs to come out. We explain what we find before any work begins.
A business that has to stay open during electrical work has different scheduling needs than a homeowner. We work around operating hours where the job allows, and we confirm the approach on the call when that is a factor. Dedicated circuits for equipment, panel capacity assessments for higher commercial loads, and outlet additions for tenant build-outs are all part of what we handle in Tempe's commercial properties.
Pricing an electrical job is not a formula. The rate reflects what the job actually involves, and several things can move it in either direction.
The fault itself matters. A loose connection at a single outlet is a different scope than a wiring fault that runs through a finished wall. What has to be opened up to reach the problem changes the time and the materials. Whether the existing circuit or panel can carry what is being added determines whether the fix is a straight installation or whether the panel needs attention first. Arc-fault and ground-fault breaker requirements under current code can also affect what a panel or circuit job involves, depending on the age of the property and what was there before.
When you call, those factors get talked through. The price is confirmed before anything is scheduled, and the scope is explained so you know what you are agreeing to. Know the price. Know the scope. Know what happens next.
Homes built during a specific stretch of the mid-twentieth century were often wired with aluminum branch circuits rather than copper. Aluminum expands and contracts differently than copper under load, which loosens connections over time and creates heat at the points where it meets devices and fixtures. The fix is not always a full rewire. Pigtailing with approved connectors or replacing the devices with aluminum-rated ones can address the risk at each connection point. A full rewire is the more thorough solution for properties where the aluminum wiring is extensive. We assess what is there and explain the options.
Properties in the Tempe area that run irrigation systems or well pumps need dedicated circuits sized for the motor load. These circuits draw more current than a standard residential circuit and need the right breaker, the right wire gauge, and a proper ground. When a pump motor fails to start or trips its breaker repeatedly, the fault is sometimes in the motor and sometimes in the circuit feeding it. We handle the electrical side: the circuit, the disconnect, and the panel connection.
Outdoor lighting in this region gets used year-round. Security lighting, landscape fixtures, and soffit or eave lights all need weatherproof boxes, conduit or rated cable, and GFCI protection at the circuit. Exterior wiring that was installed without proper weatherproofing degrades faster than interior wiring, and the failure often shows up at the fixture before it shows up in the wall. We install and replace exterior lighting, run new outdoor circuits, and bring existing exterior wiring up to current standards.
An outdoor outlet that is not properly enclosed is a moisture problem waiting to happen. In-use covers keep a plugged-in cord protected from rain and debris, and the box behind the outlet has to be rated for exterior use. We install weatherproof outlets for patios, pool areas, and exterior walls, and we replace covers and enclosures that have cracked or lost their seal.
Connecting a generator to a home's electrical system is not a matter of plugging it into an outlet. The right approach is a transfer switch wired to the panel, which lets the generator carry selected circuits without back-feeding the utility line. We handle the transfer switch installation, the wiring from the switch to the panel, and the inlet connection where the generator plugs in. The panel has to be assessed first to confirm the circuits being backed up are correctly sized for the generator's output.
Matching a replacement part to what is already in a property sounds straightforward until the property is old enough that the original fittings are no longer manufactured. Older panels take breakers that are specific to the brand and series, and a breaker that fits the slot is not the same as one that is rated for it. Outlets and switches in older homes may be wired in a way that does not match current device configurations without some additional work at the box.
When a part is obsolete, there are usually two paths: a compatible replacement that meets current code, or a more involved fix that brings the affected section up to current standards. We explain which applies before any parts are ordered. The work is local, which means it is easy to check.
If something has to be ordered rather than installed on the first visit, that gets communicated on the call and confirmed before the visit is scheduled. We do not show up and then tell you the job cannot be finished.
Recessed lighting and LED retrofits are the most common indoor lighting requests we handle. A room with a single ceiling fixture in the center reads differently once recessed lights are distributed across the ceiling, and the wiring for a retrofit job runs through the attic or ceiling space above. Ceiling fan installation is often part of the same conversation, since a fan with a light kit covers both comfort and illumination on a single circuit. When other electrical work is already scheduled, adding a ceiling fan or a set of recessed fixtures to the same visit is worth considering.
Driveway and entry lighting, motion-sensor fixtures, and soffit lights are the outdoor requests that come up most often. A motion-sensor light over a garage or a side entry covers security and convenience without running continuously. Landscape lighting on a low-voltage system still needs a properly installed transformer and a weatherproof outlet to feed it. When exterior work is being done for other reasons, running an additional circuit for outdoor lighting at the same time avoids a second visit.
Some electrical problems will not wait for a convenient window. A tripped breaker that will not reset, a sparking outlet, or a section of a commercial property that has lost power are not situations where a week from Tuesday works. We take short-notice calls when the schedule allows, and urgent electrical faults are treated as priority calls during our hours.
For properties that have to stay open or occupied during the work, the approach gets confirmed on the call before the visit is scheduled. We work around operating hours where the job allows, and we communicate what circuits will be affected and for how long before anything is shut down. That applies to apartment buildings with multiple tenants as much as it applies to a retail space that cannot close mid-day.
We are available every day from 5:00 AM to 10:30 PM.
Call (480) 923-2895 and describe what is happening.
We will confirm what the schedule allows and get something on the books. The full breakdown is on our electrical service list.
We serve Tempe and the surrounding communities throughout Maricopa County. That includes Guadalupe, Chandler, Paradise Valley, Gilbert, and Mesa.
If your property is in the area and you need electrical work handled properly, call (480) 923-2895 and we will confirm coverage for your address. Reach out and we'll get it diagnosed.
It can. If the property has restricted access, a parking structure, a gated entry, or other access considerations, let us know when the visit is being scheduled. Confirming access in advance means the visit starts without delays. We ask about access as part of the scheduling conversation.
Reset it once and see whether it holds. If it trips again immediately or will not reset at all, leave it in the off position and call us rather than continuing to reset it. A breaker that trips repeatedly under normal use is pointing to a fault that needs to be diagnosed, not a nuisance that can be managed by resetting it repeatedly.
A converted space that will be used as a living area, office, or bedroom typically needs dedicated circuits for lighting, outlets, and any HVAC equipment that feeds the space electrically. Running those circuits from the panel and confirming the panel has capacity to carry the added load is part of what we handle for conversion projects. We talk through what the space will be used for on the call so the electrical plan fits the actual need.
Yes. Some projects, such as a whole-house rewire or a panel upgrade combined with new circuit installation, can be phased across more than one visit. We discuss what can be staged and what needs to happen in a single visit when we scope the job on the call. Staging is confirmed before anything is scheduled so the plan is clear from the start.
In many cases, yes. If the work involves circuits or panel sections that do not supply the refrigerator or freezer, those appliances can stay on while the affected circuits are shut down. We identify which circuits are being worked on and which are unaffected when we scope the job, so you can plan around any shutdown that does affect the appliance circuits.
Yes. If the panel directory is missing, incomplete, or wrong, we can trace and label each circuit so the panel reflects what is actually in the property. This is particularly useful for older homes where circuits have been added or modified over time without the directory being updated. We confirm the scope of the mapping work on the call.
We identify what is wrong, explain what the correct approach is, and scope the repair or remediation before any work begins. Incorrectly installed wiring, missing grounding, improper splices, and devices wired out of code are all things we can correct. The scope of that work depends on how far the problem extends, which is confirmed during the diagnostic visit.
Any time wiring needs to be roughed in before walls are closed, or when a circuit needs to be in place before an appliance or fixture can be installed. Coordinating the electrical work with the framing, drywall, and finish trades avoids the need to open finished walls later. We confirm the sequencing when we scope renovation work so the electrical is done at the right point in the project.
Older properties and units that have been updated piecemeal sometimes have wiring that does not follow a clear map. When that is the case, we trace the circuits during the diagnostic visit, identify what is there, and explain what we find before scoping the fix. The scope and the price are confirmed before any work begins, so there are no decisions made on your behalf without your input.
Call (480) 923-2895 and we will talk through what the job involves, confirm what it costs, and get it on the schedule.
Every day from 5:00 AM to 10:30 PM, someone who knows the trade answers the call and can scope the job on the phone. Straight answers on the phone. Real electrical work. Quick to respond. The price is agreed before anyone shows up, and the scope is explained before anything is touched.
Also serving the towns around: Chandler, Scottsdale, Peoria.
Whether the call is about a dead outlet, a panel that keeps tripping, or a full service upgrade, we handle the electrical work that keeps homes and businesses running in Tempe. The table below covers what each service includes, who it fits best, and one practical thing worth knowing before you call. Pricing is confirmed on the call before anything is scheduled.
| Service Type | What's Included | Best For | What to Keep in Mind |
|---|---|---|---|
| Electrical Repairs & Troubleshooting |
| Any property with a symptom that needs a source | The visible symptom is not always where the fault lives. Tracing it to the source before replacing parts saves time and avoids repeat calls. |
| Electrical Safety Inspections |
| Home buyers, sellers, and landlords with older properties | An inspection is a useful step before a real estate transaction, when a rental property needs a compliance review, or when an older home has not had its wiring looked at in years. |
| Electrical Panel & Service Upgrades |
| Homes adding EV chargers, solar systems, or high-draw appliances | Maricopa County's long cooling season puts continuous load on panels. A load calculation confirms the service entrance can carry what is being asked of it before the upgrade is scoped. |
Call (480) 923-2895 and we will go over what the job involves, confirm the rate, and get it on the schedule.
(480) 923-2895